Free delivery on orders over £1200.00, all other orders have a fixed rate of £20.00 + VAT.
*Terms and conditions apply
If you would like to discuss this product, or you require a sample, please call 01702 560194. Alternatively, you can use our contact form.
*Terms and conditions apply
If you would like to discuss this product, or you require a sample, please call 01702 560194. Alternatively, you can use our contact form.
Please note: All cut material is non-returnable unless faulty as these are non-sellable and have been cut to specific requirements.
Blue Food Quality FDA Approved Nitrile Strip
SKU: ST-Coru166
- Approved to US FDA 21 CFR177,2600 – EU1935/2004 and USP Class V1 compliant
- REACH, RoHS, PAH and CE compliant
- Suitable for high temperatures and media containing oils, fats and greases
- FDA approved Nitrile Rubber: 60° Shore
- View material – Coru166
Call for Price
Chemical Resistances
Brine, Calcium Chloride, Carbon Dioxide, Carbon Monoxide, Castor Oil, Corn Oil, Crude Oil, Diesel Oil, Fatty Acids, Gasoline, Glucose, Grease, Heptane, Hydraulic Fluid, Hydrogen Gas, Hydrogen Sulphide, Jet Fuels, Kerosene, Lard, Lime, Linoleic Acid, Linseed Oil, LPG, Lubricating Oils, Mineral Oil, Natural Gas, Neon Gas, Nitrogen, Oil Petroleum, Oleic Acid, Paraffin Wax, Pentane, Petroleum Oils, Pine Oil, Propane, Sea Water, Sewage, Steam, Sulfuric Acid, Toluene, Transformer Oil, Urea, Varnish
Technical Information
| PROPERTIES | TEST METHOD | VALUES FPS UNITS | TEST METHOD | VALUES METRIC UNITS |
| SPECIFIC GRAVITY | ASTM D297 | 1.40 ± 0.05 | DIN 53508 | 1.40 ± 0.05 |
| HARDNESS | ASTM D2240 | 60 ± 5 SH A | DIN 53505 | 60 ± 5 SH A |
| TENSILE STRENGTH ( MIN ) | ASTM D412 | 1140 PSI | DIN 53504 | 60 KG/CM2 |
| ELONGATION AT BREAK ( MIN ) | ASTM D412 | 350% | DIN 53504 | 350% |
| COMPRESSION SET (70 ºC/24 HRS/25% SET) (MAX) | ASTM D395 METHOD B | 40% | DIN 53517 | 40% |
| TEAR RESISTANCE ( ANGULAR ) MIN | ASTM D624 | 112 LBS/INCH | DIN 53515 | 20 KG/CM |
| CHANGE IN PROPERTIES | ||||
| HEAT AGEING ( 72 HRS. AT 70 ºC ) | ASTM D573 | |||
| — HARDNESS (PTS) | + 4 (MAX) | + 4 (MAX) | ||
| — TENSILE STRENGTH (%) | + 10 / – 15 | + 10 / – 15 | ||
| — ELONGATION AT BREAK (%) | + 10 / – 20 | + 10 / – 20 | ||
| VOLUME SWELL : AT 70º C FOR 72 HRS/IN | ASTM D 471 | |||
| ASTM OIL NO.1 | + 3 % | + 3 % | ||
| ASTM OIL NO.2 | + 16% | + 16% | ||
| ASTM OIL NO.3 | + 20% | + 20% | ||
| POLYMER CONTENT (NITRILE) | 100% | 100% | ||
| CHEMICAL RESISTANCE | ||||
| — OZONE | ASTM D 1149 | FAIR | FAIR | |
| — DILUTE ACIDS AND BASES | GOOD | GOOD | ||
| — CONCENTRATED ACIDS AND BASES | NOT RECOMMENDED | NOT RECOMMENDED | ||
| — OILS | GOOD | GOOD | ||
| — SOLVENTS | FAIR | FAIR | ||
| TEMPERATURE RANGE | -25º TO + 110º C | -25º TO + 110º C | ||
| COLOUR | RAL 5012 BLUE | RAL 5012 BLUE | ||
| POLYMER CONTENT (%) | 100 | |||
Test Name – Determination of Amount of extractives
Method: With reference to US FDA 21 CFR 177.2 00
| EXTRACTANTS | TEST CONDITION | AMOUNT OF EXTRACTIVES
MG/INCH² |
ACCEPTABLE LIMIT
MG/INCH² |
CONCLUSION |
| 1 | ||||
| Distilled Water | 70 °C for 2 hours | 10 | 20 | Pass |
| n-Hexane | 70 °C for 2 hours | 100 | 175 | Pass |
| Note: | 1. mg/inch² denotes Milligram per square inch |
| 2. °C denotes Degrees Celsius |
| PROPERTIES | TEST METHOD | VALUES FPS UNITS | TEST METHOD | VALUES METRIC UNITS |
| SPECIFIC GRAVITY | ASTM D297 | 1.40 ± 0.05 | DIN 53508 | 1.40 ± 0.05 |
| HARDNESS | ASTM D2240 | 60 ± 5 SH A | DIN 53505 | 60 ± 5 SH A |
| TENSILE STRENGTH ( MIN ) | ASTM D412 | 1140 PSI | DIN 53504 | 60 KG/CM2 |
| ELONGATION AT BREAK ( MIN ) | ASTM D412 | 350% | DIN 53504 | 350% |
| COMPRESSION SET (70 ºC/24 HRS/25% SET) (MAX) | ASTM D395 METHOD B | 40% | DIN 53517 | 40% |
| TEAR RESISTANCE ( ANGULAR ) MIN | ASTM D624 | 112 LBS/INCH | DIN 53515 | 20 KG/CM |
| CHANGE IN PROPERTIES | ||||
| HEAT AGEING ( 72 HRS. AT 70 ºC ) | ASTM D573 | |||
| — HARDNESS (PTS) | + 4 (MAX) | + 4 (MAX) | ||
| — TENSILE STRENGTH (%) | + 10 / – 15 | + 10 / – 15 | ||
| — ELONGATION AT BREAK (%) | + 10 / – 20 | + 10 / – 20 | ||
| VOLUME SWELL : AT 70º C FOR 72 HRS/IN | ASTM D 471 | |||
| ASTM OIL NO.1 | + 3 % | + 3 % | ||
| ASTM OIL NO.2 | + 16% | + 16% | ||
| ASTM OIL NO.3 | + 20% | + 20% | ||
| POLYMER CONTENT (NITRILE) | 100% | 100% | ||
| CHEMICAL RESISTANCE | ||||
| — OZONE | ASTM D 1149 | FAIR | FAIR | |
| — DILUTE ACIDS AND BASES | GOOD | GOOD | ||
| — CONCENTRATED ACIDS AND BASES | NOT RECOMMENDED | NOT RECOMMENDED | ||
| — OILS | GOOD | GOOD | ||
| — SOLVENTS | FAIR | FAIR | ||
| TEMPERATURE RANGE | -25º TO + 110º C | -25º TO + 110º C | ||
| COLOUR | RAL 5012 BLUE | RAL 5012 BLUE | ||
| POLYMER CONTENT (%) | 100 | |||
Test Name – Determination of Amount of extractives
Method: With reference to US FDA 21 CFR 177.2 00
| EXTRACTANTS | TEST CONDITION | AMOUNT OF EXTRACTIVES
MG/INCH² |
ACCEPTABLE LIMIT
MG/INCH² |
CONCLUSION |
| 1 | ||||
| Distilled Water | 70 °C for 2 hours | 10 | 20 | Pass |
| n-Hexane | 70 °C for 2 hours | 100 | 175 | Pass |
| Note: | 1. mg/inch² denotes Milligram per square inch |
| 2. °C denotes Degrees Celsius |